[3-Pack]- Mr.Shield for OnePlus 6 / OnePlus Six [Tempered Glass] Screen Protector [Japan Glass with 9H Hardness] with Lifetime Replacement

Update 10/12: Changing to 5 stars because the protector saved my screen while moving a couch with my phone in my pocket. Protector was cracked but phone was fine. Just put a second one on.Pros:Easy to install with the provided guide stickers.Optically beautiful.Finger print resistant.Works with my OtterBox case.Cons:Unfortunately, as others have mentioned, the right and left sides are slightly too wide and do not fully adhere. There is about 1mm on either side that have a raised, air-bubbled appearance. This is because the phone's glass starts to curve and the screen protector hangs over this curve.This is my second screen protector from Amazon that was not perfect. The other one tried to avoid the overhang problem by making it too narrow. I think this is an extremely hard phone to make a screen protector for. I only trust the genuine OnePlus "3D" screen protector at this point. The tollerances are just too tight.The bubbles are not annyoing enough for me to remove this protector but I will be replacing it with a OnePlus protector if it happens to fall off or break.

Despite what other reviewers reported about this extending past the curved part of the screen, mine is a bit too narrow to fully cover the active part of the display. I installed it perfectly aligned on the right side and it is about 1/16" shy of covering to the left edge. There is only one small area at the bottom left where the edge did not adhere, but since it is on the inactive part of the screen it is not a big deal. Installation was simple using the included strips to make a hinge as the instructions show, however I hinged mine on the side instead of the bottom to get better control over alignment. Zero bubbles or dust specs on the first attempt.

Pros:* It adheres very well, and very quickly. I have no bubbles or rainbows* The surface feels good to the touch.Cons:Too small all aroundNotch geometry is wrongSpontaneously breaks for no reason"Lifetime Replacement Warranty" is a joke.It's too narrow. We're not talking about a couple pixels falling off the side. We're talking about a LOT of pixels on either side of the protector. Even with my case on, I can feel the edges all the way around the entire phone. I'm not expecting a perfect fit for every case, and the OnePlus 6 does have rounded edges which makes a perfect fit difficult, but this is playing it waaaaay too safe. You wanna know if it will work with your case? I'll go ahead and say "yup, you betcha". There's almost no possibility that this is going to interfere with your case. You've got plenty of room.It protected my phone from a legitimate fall and then later broke for no reason. I thought maybe it was after effects of the fall, and installed the second of the three protectors. I never dropped the phone. I never put it in the same pocket as my keys, I made sure that nothing happened to it and yet the protector was broken two weeks later. I installed the third and sent an email to the company to see about the "lifetime replacement warranty" since it was apparent that at least one of the three was defective. The email bounced because of course it did. None of my attempts to use the supposed warranty have met with any success, and by now, the third protector has also died, again with no apparent cause. The warranty appears to be a joke with nothing behind it.Look elsewhere.

Just installed the 1st of the 3 screen protectors. Based on the previous reviews it appears as though Mr. Shield had listened and trimmed the edges—just a little too much. As a result, the screen protector's short by >1.0 mm all round. Unfortunately, the problem of inconsistent adhesion around the edges continues to persists. It's as though the protector wasn't 100% planar in some places around the edges due to a barely noticeable curl of merely a few single-digit 100ths of a millimeter, which points to a cutting process that isn't 1000% dialed in yet.

The screen protector fits the phone just fine but is a little too big for the screen and has a definite halo effect where the edges don't adhere to the screen well. I'm returning this simply because if how ugly the halo effect looks

Good product!

I've used Mr. Shield screen protectors on multiple phones now and have come to trust their quality. They also provide many helpful tools for proper application. Excellent value.Unfortunately, the OnePlus 6 is just a difficult phone to make a screen protector for, due to its somewhat rounded screen edges. I did my best to line up the edges of the screen protector with the lit pixels of the screen, but as you can see in other pictures posted, there are a few rows of pixels that are not covered on both sides.I also tried to apply my screen protector as close to the bottom edge as possible without leaving a gap at the notch and without any overhang at the bottom. This way, I can keep using my swipe gestures without running over the bump of the edge. However, bubbles persist at the edge. I'm ok with it, since they don't interfere with the pixelated portion. However, looking at the phone with the screen off, you can tell, and it looks shabby.

Had no issue following the instructions provided and adhering the protector to my Oneplus 6 phone. I did already happen to drop my phone and the protector cracked but did its job because my screen underneath was fine. I have emailed the company for a replacement and I'm hoping for a quick response. Since there are 3 in a pack, have already replaced the broken one from my phone with no issues in the removal. Great product.